Metallic and rust effect paints

Classic Mettal is our range of ready-to-use metallic paints that give the coated surface an authentic metallic finish as they contain metallic particles of copper, bronze, iron and brass, depending on the desired result. The decorative possibilities of these metal paints are endless on non-trafficable surfaces such as walls or furniture. The most attractive finishes give an industrial, sophisticated and original touch to interiors and exteriors.

But the versatility of this innovative paint goes far beyond that. Thanks to the application of our rust activator Mettal Activator, Classic Mettal becomes a rust effect paint that gives the surfaces on which it is applied a very natural aged effect. A rust effect paint that is highly recommended for walls and ideal for replicating that vintage style that never goes out of fashion.

In addition to the varied decorative finishes it offers, Classic Mettal stands out for being a metallic and rust effect paint with great durability, excellent adhesion and high resistance to weathering if the appropriate varnish or sealant is applied. This is why it can also be used without any problems on exterior surfaces such as building facades, pillars or walls.

Types of Classic Mettal metallic and rust effect paints

At Topciment we have five types of Classic Mettal metallic and rust effect paints: Copper, Bronze, Iron 004, Brass and Iron 030. Each of them offers unrepeatable decorative finishes as they allow you to play with the mixtures in such a way that no two coatings will be the same, especially if you use our rust accelerator Mettal Activator.

Tehnične podrobnosti

Poraba

The consumption of Classic Mettal metallic and rust effect paints will depend on the substrate to be coated and the application method In a trowel application, the coverage is the following: 0,15 L/m².

Vrste Classic Mettal

Pakiranje

Klasične kovinske barve Metal in barve z učinkom rje so na voljo v posodah po 1L.

Classic Mettal metallic and oxide finishes

Below we show the different metallic (left) and oxide (right) finishes that can be achieved depending on the chosen Classic Mettal pigment.

Copper + Mettal Activator

Brez oksidaBrez oksida

Bronze + Mettal Activator

Brez oksidaBrez oksida

Iron 004 + Mettal Activator

Brez oksidaBrez oksida

Iron 030 + Mettal Activator

Brez oksidaBrez oksida

Brass + Mettal Activator

Brez oksidaBrez oksida

Where to apply Classic Mettal metallic and rust effect paints

Classic Mettal paints can be applied on almost any type of material. They are compatible with microcement, concrete, brick, ceramic, glass, plaster, plasterboard or paper, among others. In this sense, it is highly recommended for use as a paint for metal due to its high content of metallic particles.

You will get the most out of walls, ceilings, facades, walls, pillars and furniture with Classic Mettal. You will be able to transform any room into a completely new one that will not leave you indifferent.

Classic Mettal can be applied by trowel, brush, brush, sponge, roller or spray.

Uporaba kovinskih barv in učinka rje Classic Mettal

Korak 1 Čiščenje in priprava podlage.
Prepričajte se, da je dobro utrjen, suh in po potrebi brušen. S sesalnikom očistite podlago.

Koprak 2 Temeljni premaz
Nanesite en sloj osnovnega premaza Primacem ABS (vpojna podlaga) ali premaza Primacem PLUS (nevpojna podlaga). Pustite, da se posuši približno 1 uro.

Korak 3 Dekoracija
Z gladilko ali valjčkom nanesite eno ali dve plasti želenega izdelka Classic Mettal (baker, bron, železo 004, železo 030 ali medenina) in pustite, da se vsaka plast posuši od 2 do 4 ure. Pustite, da se 24 ur posuši.

Korak 4 Kovinski zaključek in tesnilo.
Če je potrebna kovinska obdelava, potem ko je površina okrašena, nanesite dva sloja laka Topsealer WT One Coat (ki omogoča 24-urno sušenje med nanašanjem), da zaščitite podlago. Pustite, da se posuši 24 ur.

Korak 5 Oksidiran zaključek in tesnilo.
Če iščete rjavo površino, potem ko je površina okrašena, nanesite Mettal Activator, da pospešite oksidacijo in pesek. 24 ur kasneje nanesite dva sloja pripravljalnega sredstva (omogočite 4 ure med sloji) in pesek. Na koncu površino zaščitite z dvema slojema laka Topsealer WT One Coat (24 ur med nanosom). Pustite, da se posuši 24 ur.

Bi radi vedeli prvi?

Sledi nam na socialnih omrežjih!